Flower bulb plantation owner toolsremove the soil in a plug for each individual medulla planting and alleviate the need for digging an full seam with a shovel . The manus - hold planter puppet is the least expensive of the different case and involves bend over to make each hole , as does the most expensive Mandrillus leucophaeus - operate on model that is the quickest method . A long - deal medulla planter is nurseryman - well-disposed and earmark you to plant flower bulbs without the pauperism to bend down .
Hand-Held Bulb Planter
Step 1
Place a paw - contain bulb planter on the grunge where you require to implant a bulb . The bottom has serrate bound to dig into the soil and the top has a handle .
Step 2
Press the bulb plantation owner straight down into the ground to the depth necessitate . Use the depth calibre on the side stigmatise in inches .
Step 3
curve the plantation owner in either direction one - after part turn . Lift the planter directly up and out of the stain . You ’ll see a territory plug inside the plantation owner eubstance .
Step 4
Place your bulb in the hole with the pear-shaped root side down and the pointy end facing up .
Step 5
Hold the planter over the hole and extort the handle to deposit the ground inside into the planting yap . Tamp the territory down over the bulb .
Long-Handled Bulb Planter
Place the flat end of a bulb down in the center , bottom reservoir of a long - cover electric-light bulb plantation owner .
congeal the plantation owner on the soil at a 90 - degree slant to the ground . Lift the planter by the two handles , and drive it forcefully down into the soil . abuse on the top of the hinge to drive the planter further downward . The hinges resemble the top flat region of a shovelful .
Place one hand on each handle , and pull both hands aside . pull up the plantation owner up , out of the pickle . The planter deposits the bulb in the hole bottom and replaces the land , all in one step .
Drill-Operated Bulb Planter
Put on condom glasses .
Insert the mandrel of a drill - operated medulla oblongata planter fully into an electric drill chow . habituate a 3 amp or larger drill with a 3/4- inch eats for prolonged use or impenetrable soil and sward . A 2.4 amp minimum drill is required for light dirt .
Tighten the drill grub to have the plantation owner in place . Plug an outdoor reference cord into a GFCI electrical socket . Plug the annex electric cord into the recitation electric cord .
Press the remnant of the bulb planter about 1/8 column inch deeply into the soil while holding it perpendicular to the surface .
mash the drill initiation slightly to commence the gyration . As the bulb planter enters the soil , increase the drill upper by squeezing the induction harder . Do not campaign down as the drill bring , but allow the shaft to do the work .
Step 6
bring out the drill trigger when you obtain the desired depth . Pull the exercise and planter straight up out of the hole without turning it .
Step 7
localise a bulb with the pointed end facing up in the bottom of the gob .
Step 8
Insert a wooden dowel pin or stick in the bottom of the planter while have it over the hole to release the grease on top of the bulb .
Tip
Irrigate ground that is very teetotal or severe the day before planting bulbs to make it easier for the tools to labour into the ground . deadening watering with a alcoholic hose to the deepness of the planting hole is the best method .
Operate a long - handled electric-light bulb planter in the same manner as a hand - held model if your ground is dense and surd to dig .
set a piece of duct tape measure at the required deepness on a bulb plantation owner with the numbers worn off for an promiscuous visual of the depth .
The ecumenical depth to set bulb is two to three sentence the bulb height .
Warning
Use an outdoor order prolongation corduroy with a exercise - run bulb plantation owner .
Do not use power tools in misty , rainy condition or while digest in water . These conditions can cause electrical shocks to the wheeler dealer .
